How To Change Dryer Blower Wheel, Whirlpool

Ask our experts a question about this office and we'll get dorsum to you every bit shortly equally possible!

six questions answered by our experts.

My fan blower was not turning. I put wd40 in it and information technology started to turn. I was cleaning the surface area with the vacuum cleaner, lost my balance and the finish of the vacuum went into the cage and broke several fins. How do you lot remove the cage?

For model number 110.70992990

Hullo Linda, Thank y'all for your research. I have constitute a video on our website that you may reference on how to supervene upon the blower bicycle. You will find it under part number PS11743785. I hope this helps. Thank you and have a great 24-hour interval!

6 people found this helpful.

Was this helpful?

Thank you for voting!

Do i demand a special tool to remove and replace the blower wheel ??

For model number MAYTAG DRYER Model MEDC700VW0.

Hullo Rick, cheers for your question. You will not demand any special tool. You would take a 7/sixteen wrench and put it on the motor shaft behind the blower bike housing to hold the blower wheel in identify. So you would take a 1/2 inch ratchet with extension and put it into the blower wheel. There should be arrows on the blower wheel that tell y'all which mode to turn information technology. I hope this helps!

6 people constitute this helpful.

Was this helpful?

Cheers for voting!

How practice I remove the blower fan?

For model number MEDX700XW0

Hello Nib, Thanks for your question. Unplug the dryer. Remove the screws on the top and remove the top panel. Remove the forepart console. Release the locking tabs from the wire harness to pull it off the board. Remove the panel that holds the control board at the back of the dryer - unscrew it and set it aside. Take out the screws that concord the console mountain plate on. Remove the access console at the bottom of the dryer. Remove the ii lower screws on the front end panel and the door switch wiring harness, taking the plug apart in the process. Open up the dryer door and remove the screws for the lint housing. Shut the door and take the pinnacle screws off of the panel (be careful that the panel does not autumn). Pull the panel off slowly then you lot do not tear the seal behind it. Disconnect the moisture sensor wire harness, then remove the front bulkhead by lifting information technology out of the dryer. Clean out any lint in the fan. Remove the belt from the idler pulleys. Remove the drum. Use a wrench and a ratchet to help remove the fan (you may need a chisel if it is stuck badly). Pull the extension out and then yous tin remove the blower wheel. Reverse this process to install. I hope this helps.

3 people found this helpful.

Was this helpful?

Give thanks yous for voting!

The video you ref. To remove a blower is of a rear unit. My blower is in the forepart, and appears to have some alan head screw holding it on. Or does the blower itself spiral off merely like the one in the video? I don't meet why i'd need to unmount the motor, tin't i just hold it somehow if the blower does just demand unscrewed, and reverse threaded im sure.

For model number MEDX500XW0

Hello Ron, Thanks for the question. Use a wrench and a ratchet to aid remove the fan (you may demand a chisel if it is stuck badly). Pull the extension out and so you lot can remove the blower bike. Reverse this process to install. I hope this helps.

1 person found this helpful.

Was this helpful?

Thank you for voting!

My fan turns freely on the shaft (it's stripped plain) so how practice i get it off? The video instructions listed under this function are not correct.

For model number 11085081401

Hi Sandy, Thank you lot for your question. The office number referenced in the previous question is meant every bit a general video to requite information on how to install the part. For more data regarding on how to remove the blower wheel from your dryer, yous will need to consult your owner's manual or check with the manufacturer. I hope this helps.

1 person constitute this helpful.

Was this helpful?

Give thanks you for voting!

I'grand looking for this part can yous help me ? I'm looking for a blower fan.

Hello Corinda, Thank you for contacting us. Please feel free to contact Customer Service at i-888-738-4871 from viii:00 AM to ten:00 PM Eastern time, seven days a week if you lot need help placing an lodge. We are looking forrad to hearing from yous!

Was this helpful?

Cheers for voting!

Source: https://www.partselect.ca/PS11743811-Whirlpool-WP697772-Blower-Wheel.htm

Posted by: gasparsible1980.blogspot.com